Hot Sales Customer Service Long Queue Buzzer Wireless Restaurant Waiter Table Pager Cafe Guest Call Bell System

RM600.00

Malaysian ringgit (RM) - MYR

Malaysian ringgit (RM) - MYR
Euro (€) - EUR

SKU: 105671423788 Category: Pagers

Description
Reviews (0)

Product Description

Wireless Coaster Pager Restaurant table buzzer Queue Management System KL-QC03

Parameter
Power input	DC12V/2A
Transmitting frequency	433.92MHz
Transmit Power	23dBm
Standby power	<120mW
Modulation Type	OOK
Max Capacity	998 pagers
Backup Battery	Li-ion 3.7V 1000mAh
Size	11016550mm
Output	DC5V/2A*2

Parameter
Battery	Li-ion 3.7V 300mAh
Receiving frequency	433.92MHz
Stand-by current	<12mA
Standby Duration	10h
Receiving sensitivity	-108dBm
Max Distance	500m in open area
Prompt Mode	Vibration/Beeping/Flashing
Prompt Time	1-999s
Input	Type-C DC5V 2A / DC12V 1A

Instruction

A.Before using

Wiring: Host connects to power source via adapter. Charging base connects to host via Type-C cable.
Connect host to power source, and charge pagers for 10 minutes at least before using.
Charging Indicator Information:

Host			Pager
Red LED	Charging	Flashing	Charging
Green LED	Full Charged	Always On	Full Charged

B.Operating Instruction

CALL mode is the default mode. Continuously press Delete button (←) to return Call Mode while in other mode. C— is displayed in CALL mode.
Input the number and press CALL button to call the corresponding pager.

C.Use

Input number and press CALL, the corresponding pager will alarm to remind. If input wrong numbers, press to delete. Pressing also can cancel a calling.

C.Mute mode

Press MUTE and 999 (S999 displayed) then press CALL, all charging pagers change to MUTE mode.
Press MUTE and 000 (S000 displayed) then press CALL, all charging pagers change to normal mode.
In MUTE mode, all pagers only vibrate and flash while being called.
Continuously press DELETE button (←) to return CALL mode. (C— displayed).

D.Call History

Press button H to check the recent 10 called numbers (HXXX displayed). Press △/▽ button to page up/down.
Continuously press DELETE button (←) to return CALL mode. (C— displayed)
Note: No looping of △/▽.

E.One-Call-Off

In CALL mode, press 999 and CALL, all charging pagers will be off. Re-charge pagers will turn on again.
Note: This instruction is invalid to the pagers not being charged.

F.Host Off

When powered by battery, long press H and △ at same time, host is off. Long press H and ▽, host is on. This operation is invalid when powered by power source. bottles in all shapes.

G.Program Operation

All pagers are programmed before delivery. So this operation is only necessary when adding new pagers or changing numbers.
Put the pagers on the charging base, press P and 999 (P999 displayed), then press CALL to enter programming mode. The operation must be finished in 20 seconds after pagers are charged.
In programming mode, all LED display of the pagers will keep flashing.
Then input number and press CALL, all pagers display this number. Move the top pager away, the pager will beep once and stop flashing. It means the pager is programmed.
Repeat the steps to program other pagers.
Note: The pagers will quit programming mode if no operation within 1 minute. All pagers’ numbers will not change if not being programmed.
1 pager only can be programmed 1 number. Old number will be replaced by the new one.s in all shapes.

Instruction Description

Common Troubles and Solutions

Reviews

There are no reviews yet.